Tuesday, October 15, 2013

TerraTrike Velomobile 99% Skinned

Another good day here at the Tinker's Workshop with progress again being made on the TerraTrike Velomobile project.  I was able to climb into the vehicle for the first time since I started skinning it and figured out where to put my speedometer and eliminate some problems in the process.  I also completed skinning of the hood that will allow me access to get in and out of the velomobile. 


With the hood finally skinned with 1/4 thick foam strip the smooth shape is really coming together.  It took me four hours to do this work and I am happy with the results.  


 This is a good shot of the nose and hood from the front of the velomobile.  I will be more than happy to get the outer skin fiber glassed as just the simplest thing can put a dent in it.  Easy enough to repair but just one more thing to be careful of while working around the vehicle at this point.  You can just see the hinges for the hood just above the nose in this shot.  I still have to grind down some of the wooden mounts so that once the body is fiber glassed very little of the hinges will be seen.  A nice look to be sure.


Another good shot of the left side of the velomobile.  You can see some of the indentations in the foam on the side of the body.  Again this is an easy fix as the body still needs to be completely sanded into shape before fiber glassing can begin.  All the little voids that I can see in between the foam strips will be puttied with an epoxy resin/micro balloon mixture and then more sanding to get the body just right. 
  Before any of this work can begin I will have to fiber glass the underside of the newly skinned hood.  I have to cut the ribs where the hood seam will be next and then the glassing can begin.  Not a hard  task to cut the hood from the body but just something that I will have to be careful with so that I don't make more work for myself in the process.


I am currently still working on the final details that will complete the tail end of the vehicle and I should have everything pretty much ironed out in the next few days.  Once I get parts made I will post that portion of the assembly when I get that far along.


One other thing that I saw today that I want to change is the opening of the cockpit for the velomobile.  As I sat in it  I was able to take a good look at how much room I actually need.  In this photo you can see a foam strip that I laid down on top of the body.  I plan on closing up the cockpit opening to fill in the small triangular area that you see here.  This will make the cockpit look a bit more closed in.  But not make it so small that I will have a hard time sitting in the drivers seat.  Still will have lots of shoulder room. 
  Total hours on the project so far have now jumped up to 338.5 hours.  A lot of work but fun work. As long as it puts a smile on my face it is time well spent. 

Sunday, October 13, 2013

TerraTrike Velomobile Wireless Brake Light

I wanted to get this post out a few days ago and finally found the time to get photos taken of the new brake light that I will be mounting into the TerraTrike Velomobile that I have been working on.  The light I choose to use comes from the Maxxon company that makes this light.


This little light has five very bright LED's and holds 2 AAA batteries.  It is approximately 2.75 x 2.75 x 1 inch in size.  The light has three different modes.  Steady, flashing, and daylight mode.  The light responds to movement and will automatically brighten when you come to a stop.  It also has a power-on and power-off capability to conserve battery power. The light came with all the hardware needed to mount to a standard bicycle but in my use this was not needed so again I sat down at the computer and worked up an enclosure for the light.


Since I needed to be able to turn on the light I designed the enclosure for that purpose.  On the side of the light is a button to turn the light on and off.  So with that in mind the enclosure needed to be shaped so that I could get my finger on to the button easily.  This is the reason for the bump out on the top of the yellow case. I used my trusty Makerbot 3D printer once again to make the enclosure which measures 4.25 x 2.5 x 2 inches in size.


The light is surrounded by a red face plate which holds the light securely into the yellow enclosure by the use of 4mm machine screws and threaded couplers.  The couplers will be permanently mounted into the enclosure which will then be imbedded into the body at the rear of the velomobile.  To remove the light for battery replacement I only have to unscrew the face plate and the light will easily slide out.  With the addition of the flashing tail light assembly that I had already designed and built this will make driving the velomobile just a bit safer when someone is following me on the street.  
 Once I get the final design of the rear end of the velomobile figured out I will install the inclosures for the lights and post photos to show you how it will all look in the body of the velomobile.

Saturday, October 12, 2013

TerraTrike Velomobile Nose Job

The last couple of days I have been collecting bits and pieces still needed for my velomobile project and working out various ideas that have come to me during this build.  One of the major things that I wanted to refine on my design was the shape of the nose on the velomobile.  


As you can see from this shot of the body the nose of the velomobile is rather blunt.  Not what I had in mind for the design and so I rolled up my sleeves once again here at the shop and started the surgery to give my creation a beautiful new nose.


In this photo you can see where the nose is and where I want it to be when I get done.  Quite a difference to be sure.


One inch foam was cut and shaped to fill the void that the first foam strip showed me was needed.  I wanted to make sure that the radius of the nose blended in nicely to the sides of the body.  I then added another piece of one inch foam to give me the shape for the top of the nose that would also blend into the body. 


 Five more layers of foam were cut and shaped to stack up on the first horizontal piece that was mounted earlier.  I was not to concerned about getting everything perfect at this point as I told my brother who had seen this photo... "It has to get ugly before it gets pretty."  This is the case for sure.


With the upper portion of the nose pieces hot glued into place the next step was to sand them down for a final layer of foam strips.


After about ten minutes of sanding the nose at this point was slowly starting to take shape.  Still not to the pretty stage yet but getting there. 


 After cutting and fitting all the little foam strips for a couple of hours to match the rest of the body I then declared that the operation was a success.  Now the velomobile has a nose on it that I call pretty. 


Here is another shot of the velomobile with the new nose or at least the top of the new nose completed.  The opening in the body at the front of the velomobile on both sides will be where the signal lights will be mounted.  As soon as I can get the needed hardware for the housings I will post photos of that portion of the build. 


Having completed the top portion of the nose I turned the body upside down once again and started work on the lower portion.


Here as before I added layers of one inch foam to get ready for the shaping and foam strips. This will be the same as the upper portion of the nose so there should be no surprises with getting it all smoothed out and looking the way I want it to be. The lower portion of the nose is smaller and so fewer layers of foam are needed to fill the voids to get a good shape.


 To finish off the installation of the foam strips to the bottom of the nose took two hours more time of cutting and fitting.  Just like a puzzle but the effort was worth the result.


With the completion of the work on the nose I now have a very streamlined shape that I have had in my head and can now be proud to show off.  
  Hours on the project have been adding up quickly now with the 3D printing of the signal light housings nearing completion today and the work that you see here.  Grand total now stands at 329 hours. Time to put my tools down again for the day and sweep up the dust.  Have a good day in your shop.  I know I've had a good one. 

Tuesday, October 8, 2013

TerraTrike Velomobile Tail Light From Design To Reality

A couple of days ago I posted a computer design that I put together of the new tail light assembly that I have planned for the TerraTrike Velomobile project.  Today all the pieces of the puzzle came together so I thought I might as well show you how it all turned out.


 Shown in this photo are all the components for the tail light assembly.  The yellow box shape in the upper left is the outer housing.   To the right of this is the inner light mount, then the ultra bright Hotshot bicycle light from Cygolite.  Then the red face place below the light and finally the 4mm bolts and threaded rod connectors.


First the light is slid into the inner light mount with a small clip that is on the back of the light.


Next the light and mount are inserted into the outer housing.


Finally the red outer face plate is added to the assembly and held into place using the 4mm hardware.  This outer face plate frames the flashing tail light perfectly and keeps the light locked into the outer housing. This housing will then be mounted permanently into the rear of the velomobile and will never be removed.  To turn the light on or off or change the flashing pattern of the light is accomplished with two external buttons on the face of the light.  The internal rechargeable battery in the light will only have to be recharged once every 100 to 500 hours or so.  This all depends on the flashing pattern that is chosen while in use.  
  The 3D printer did a wonderful job of making the parts for this portion of the project and it is a shame that the only thing that anyone will see of the light will be the red face plate and the light itself once it is mounted into the body.  The rest of the yellow outer housing will be hidden in the body of the velomobile.  I am just happy it turned out as well as it did and will make it that much safer for me to drive the velomobile night or day. So this is just one more thing that I can cross of my to do list on this project.  Total hours now have come up to 292 hours.  A long build but with some nice results for my efforts.

Sunday, October 6, 2013

TerraTrike Velomobile Fiber Glassing, Signal Lights and More!

Hello Everyone!  This past week has been a busy one for me with all that I managed to get accomplished.  I thought it was about time that I got another post put out to show you all the neat things that are happening here at The Tinker's Workshop.  
  First off on my list has been the completion of the the skinning of the bottom nose section of the body for the velomobile.



The difficult part of skinning this section of the body was that the inside half of the nose at this point in the build is an open cavity.  This makes it a real task to glass both sides of the foam strips that I needed to put on.  I taped the foam strips together first and then inserted all the strips into their proper location on the body without gluing them.  The middle section of this panel was then fiber glassed on the outside and let to dry.



Once the fiber glass had cured I was able to remove the panel of foam strips and then fiber glass the inner side of the panel. This would strengthen as well as seal this portion of the body.


The panel at this point was then reposition back on to the under side of the nose after it was trimmed to size.  I made an epoxy putty that I spread on the contacting faces of the body and again taped it down to cure over night.


 Now the panel is bonded into place and is done until final shaping of the body takes place.

  The next order of business that I had to work on this week were the signal lights that I have planned for the velomobile.  This has been a major task in itself just trying to figure out how to make them or even find a light system that would work that was not overly expensive or complicated to put together. 


The photo above shows what I found on Ebay that I think will fill the bill.  These are emergency lights for a  car or a truck that can be put into a back window of the vehicle.  I needed something that could run on 12 volts of power and flash bright enough to be seen during the daytime.  Each light has 22 LED's in them and after I hooked up a 12 volt power supply ( 8 double  A's in a holder)  the little black box which is the  controller makes all the lights flash without a hitch and I was in business. I will use two sets of lights to make the left and right turn signals.  Then all I need to do is connect them to a double pole double throw switch and the power pack and I have signal lights.


Next I removed the lower mounting that came with the lights as they would not work with what I have planned. 



I had to work on a new mounting that I designed for the velomobile body and made on my 3D printer.  This was a simple task of having the mounting encase the light and have mounting points on the ends  to secure it to the next portion of the assembly.  Four of these mounts needed to be made for the project. 


This photo is one of the biggest parts I've ever had to design and make on my 3D printer.  This is the housing that the signal light fixture will be mounted to.  This housing will be fiber glassed into the body and two will be needed in the front and two in the rear to hold the signal lights.  


Here the signal light is mounted into the open side of the housing that will display the signal light when it is in use.  The white housing stands 5 1/2 inches high, 6 3/4 inches long and 3 1/2 inches deep.  This one shown is for the front of the vehicle and the rear housings are similar but just a little shorter in length.  This housing alone takes 10 hours to print on my 3D printer.  So it's a very long day to complete just one of these parts.  Luckily I only have to make four of them.   I also figured out that each housing only cost me around $7.25 each to make.  A far cry from having some company charge me an arm and a leg for what I can do myself.  (My 3D printer just paid for itself again.)
  The four holes in the face of the housing will be used to mount a plexiglass window over the signal lights.  This will give the entire assembly a very smooth look once mounted into the body of the velomobile. 


The next task that I dealt with this week was a flashing light that I wanted for the rear end of the velomobile.  I wanted something easy to mount, as bright as possible and of course not a lot of money.  This little bicycle light from Cygolight called the Hotshot will fit the bill perfectly.  It is rechargeable, can be turned on with buttons on the face, is very light weight and only cost around $30  I turned the light on and was nearly blinded by the 2 watt LED that is in it.  I think you could see this light at night at least a couple of miles away. 



As I again did not need or want the mount for a standard bicycle I removed it and started work on the new housing for this light to be put into the rear of the velomobile. This is a little light as it is only 2 1/4 inches long by 1 1/2 inches wide and only around an inch deep.





 To get the new mount for the strobe light figured out I had to first model it in my CAD software on the computer.  The pictures above show you how my efforts turned out.  The back of the light has a belt clip that I did not want to try to remove as I might damage the light.  Not a good idea so I left it on and incorporated it into my design.



I designed a little base the this rear clip will slide into.  I'll print it first on my 3D printer to make sure it fits securely. 



Next comes the enclosure that the light and base mount will be inserted into. This enclosure will be fiber glassed into the rear portion of the body of the velomobile. This enclosure is only 2 inches by 4 inches in size and 2 inches deep.




This is how the assembly will look once the light and the base mount have been installed into the enclosure.






To finish off the assembly an outer cover plate will be mounted and attached to the assembly using machine screws and inner connectors that are mounted into the bottom portion of the blue enclosure.  I'll paint this cover plate a bright red so that it will show up nicely during the day time.  The only thing you will see of the assembly once it has been installed into the velomobile is the cover plate and the light.  To remove the light to recharge it I only have to take out  two screws and the light will come right out.  But from the specs on the light I should not have to do this more than once or twice a riding season.  
  So you can see I have been a busy guy here at the Tinker's Workshop this week and it doesn't look like things will slow down any until cold weather sets in.  Total hours of work on the project so far has risen to 262 hours. With the printing of the signal light housings this total will jump up very quickly in the coming days. 
   I still have a lot of fiber glassing I want to complete before cold weather sets in and work on another mounting for a brake light assembly that I am waiting for in the mail.  This and a list of other things that seem to get longer every day for this project.  But all of it is what puts a smile on my face so it is all worth it.  Enjoy the photos and I'll keep you up to date as I go further with the TerraTrike velomobile project.